mirror of
https://github.com/adrcs/ip400.git
synced 2025-04-22 19:43:44 +03:00
91 lines
3 KiB
Plaintext
91 lines
3 KiB
Plaintext
########################################################################
|
|
# EEPROM settings text file
|
|
#
|
|
# Edit this file for your particular board and run through eepmake tool,
|
|
# then use eepflash tool to write to attached HAT ID EEPROM
|
|
#
|
|
# Tools available:
|
|
# eepmake Parses EEPROM text file and creates binary .eep file
|
|
# eepdump Dumps a binary .eep file as human readable text (for debug)
|
|
# eepflash Write or read .eep binary image to/from HAT EEPROM
|
|
#
|
|
########################################################################
|
|
|
|
########################################################################
|
|
# Vendor info
|
|
|
|
# 128 bit UUID. If left at zero eepmake tool will auto-generate
|
|
# RFC 4122 compliant UUID
|
|
product_uuid 00000000-0000-0000-0000-000000000000
|
|
|
|
# 16 bit product id
|
|
product_id 0x0000
|
|
|
|
# 16 bit product version
|
|
product_ver 0x0000
|
|
|
|
# ASCII vendor string (max 255 characters)
|
|
vendor "ACME Technology Company"
|
|
|
|
# ASCII product string (max 255 characters)
|
|
product "Special Sensor Board"
|
|
|
|
|
|
########################################################################
|
|
# GPIO bank settings, set to nonzero to change from the default.
|
|
# NOTE these setting can only be set per BANK, uncommenting any of
|
|
# these will force the bank to use the custom setting.
|
|
|
|
# drive strength, 0=default, 1-8=2,4,6,8,10,12,14,16mA, 9-15=reserved
|
|
gpio_drive 0
|
|
|
|
# 0=default, 1=slew rate limiting, 2=no slew limiting, 3=reserved
|
|
gpio_slew 0
|
|
|
|
# 0=default, 1=hysteresis disabled, 2=hysteresis enabled, 3=reserved
|
|
gpio_hysteresis 0
|
|
|
|
# If board back-powers Pi via 5V GPIO header pins:
|
|
# 0 = board does not back-power
|
|
# 1 = board back-powers and can supply the Pi with a minimum of 1.3A
|
|
# 2 = board back-powers and can supply the Pi with a minimum of 2A
|
|
# 3 = reserved
|
|
# If back_power=2 then USB high current mode will be automatically
|
|
# enabled on the Pi
|
|
back_power 0
|
|
|
|
########################################################################
|
|
# GPIO pins, uncomment for GPIOs used on board
|
|
# Options for FUNCTION: INPUT, OUTPUT, ALT0-ALT5
|
|
# Options for PULL: DEFAULT, UP, DOWN, NONE
|
|
# NB GPIO0 and GPIO1 are reserved for ID EEPROM so cannot be set
|
|
|
|
# GPIO FUNCTION PULL
|
|
# ---- -------- ----
|
|
#setgpio 2 INPUT DEFAULT
|
|
#setgpio 3 INPUT DEFAULT
|
|
#setgpio 4 INPUT DEFAULT
|
|
#setgpio 5 INPUT DEFAULT
|
|
#setgpio 6 INPUT DEFAULT
|
|
#setgpio 7 INPUT DEFAULT
|
|
#setgpio 8 INPUT DEFAULT
|
|
#setgpio 9 INPUT DEFAULT
|
|
#setgpio 10 INPUT DEFAULT
|
|
#setgpio 11 INPUT DEFAULT
|
|
#setgpio 12 INPUT DEFAULT
|
|
#setgpio 13 INPUT DEFAULT
|
|
#setgpio 14 INPUT DEFAULT
|
|
#setgpio 15 INPUT DEFAULT
|
|
#setgpio 16 INPUT DEFAULT
|
|
#setgpio 17 INPUT DEFAULT
|
|
#setgpio 18 INPUT DEFAULT
|
|
#setgpio 19 INPUT DEFAULT
|
|
#setgpio 20 INPUT DEFAULT
|
|
#setgpio 21 INPUT DEFAULT
|
|
#setgpio 22 INPUT DEFAULT
|
|
#setgpio 23 INPUT DEFAULT
|
|
#setgpio 24 INPUT DEFAULT
|
|
#setgpio 25 INPUT DEFAULT
|
|
#setgpio 26 INPUT DEFAULT
|
|
#setgpio 27 INPUT DEFAULT
|