mirror of
https://github.com/adrcs/ip400.git
synced 2025-04-18 18:13:44 +03:00
68 lines
2.3 KiB
Plaintext
68 lines
2.3 KiB
Plaintext
########################################################################
|
|
# EEPROM settings text file
|
|
#
|
|
# Edit this file for your particular board and run through eepmake tool,
|
|
# then use eepflash tool to write to attached HAT ID EEPROM
|
|
#
|
|
# Tools available:
|
|
# eepmake Parses EEPROM text file and creates binary .eep file
|
|
# eepdump Dumps a binary .eep file as human readable text (for debug)
|
|
# eepflash Write or read .eep binary image to/from HAT EEPROM
|
|
#
|
|
########################################################################
|
|
|
|
########################################################################
|
|
# Vendor info
|
|
|
|
# 128 bit UUID. If left at zero eepmake tool will auto-generate
|
|
# RFC 4122 compliant UUID
|
|
product_uuid 00000000-0000-0000-0000-000000000000
|
|
|
|
# 16 bit product id
|
|
product_id 0x0001
|
|
|
|
# 16 bit product version
|
|
product_ver 0x0002
|
|
|
|
# ASCII vendor string (max 255 characters)
|
|
vendor "Alberta Digital Radio Communications Society"
|
|
|
|
# ASCII product string (max 255 characters)
|
|
product "IP400 E04 HAT Rev A"
|
|
|
|
|
|
########################################################################
|
|
# GPIO bank settings, set to nonzero to change from the default.
|
|
# NOTE these setting can only be set per BANK, uncommenting any of
|
|
# these will force the bank to use the custom setting.
|
|
|
|
# drive strength, 0=default, 1-8=2,4,6,8,10,12,14,16mA, 9-15=reserved
|
|
gpio_drive 0
|
|
|
|
# 0=default, 1=slew rate limiting, 2=no slew limiting, 3=reserved
|
|
gpio_slew 0
|
|
|
|
# 0=default, 1=hysteresis disabled, 2=hysteresis enabled, 3=reserved
|
|
gpio_hysteresis 0
|
|
|
|
# If board back-powers Pi via 5V GPIO header pins:
|
|
# 0 = board does not back-power
|
|
# 1 = board back-powers and can supply the Pi with a minimum of 1.3A
|
|
# 2 = board back-powers and can supply the Pi with a minimum of 2A
|
|
# 3 = reserved
|
|
# If back_power=2 then USB high current mode will be automatically
|
|
# enabled on the Pi
|
|
back_power 1
|
|
|
|
########################################################################
|
|
# GPIO pins, uncomment for GPIOs used on board
|
|
# Options for FUNCTION: INPUT, OUTPUT, ALT0-ALT5
|
|
# Options for PULL: DEFAULT, UP, DOWN, NONE
|
|
|
|
# GPIO FUNCTION PULL
|
|
# ---- -------- ----
|
|
setgpio 10 OUTPUT NONE # BOOT_ENA
|
|
setgpio 11 OUTPUT NONE # RESET
|
|
setgpio 14 ALT0 DEFAULT # TXD0
|
|
setgpio 15 ALT0 DEFAULT # RXD0
|